Blank End Cap Oil Seals

These blank end cap oil seals are commonly used in general machinery, to close off unused bearing housing bores.

381 products

Loading filters…

Blank End Cap Oil Seals

What is a blank end cap seal?

A blank end cap seal is a solid, disc-shaped seal that closes off a bore in a housing where no shaft passes through. It works like a plug: it presses into the housing bore to keep lubricant in and dirt and water out, but has no hole in the middle. Blank end cap seals are often called VK seals, and are used to cap the ends of bearing housings, gearboxes, and machine frames.

A standard blank end cap seal is made up of:

  • A steel body, which gives the seal its strength and keeps it flat
  • A nitrile rubber covering, which seals against the housing bore and protects the steel
  • A solid, closed face with no hole for a shaft
  • A rubber outer surface that grips the bore for a secure, leak-free fit.

The rubber-covered steel design makes them simple and reliable.

  • The steel body holds its shape when pressed into the bore, while the rubber covering seals against any small imperfections in the housing.
  • Because the cap sits inside the bore, it does not add to the width of the installation, unlike a bolt-on end cover.

Blank end cap seals are sized by their outside diameter and width. For example, an 85x9 seal fits an 85mm bore and is 9mm wide.

Why are blank end cap seals essential?

Many housings have bores where no shaft comes out, either at the closed end of a shaft or where a hole is left over from manufacturing. These openings need to be sealed, or oil will leak out and dirt and water will get in. A blank end cap seal closes the opening quickly and cheaply, with no machining, bolts, or extra parts.

They are low in cost, easy to fit and remove, and take up no extra space outside the housing. This makes them a simple way to seal off unused bores and protect bearings and gears inside.

Typical applications include:

  • Closed ends of bearing housings
  • Gearboxes and reducers
  • Pump and motor housings
  • Wheel hubs and axle ends
  • Agricultural and construction machinery
  • Blank holes left from machining or casting
  • Machine frames and covers

The main types of blank end cap seals

  • Standard blank end cap seals - The most common type, with a flat steel body fully covered in black nitrile rubber. They suit most housings and general applications.
  • Stepped blank end cap seals - These have a stepped profile with two thickness figures, which suits housings with a particular bore depth or shoulder.
  • Coloured blank end cap seals - Versions in blue nitrile rubber, which are easy to identify and spot if they become loose.
  • Wide blank end cap seals - Wider seals for larger or deeper bores, which give a more secure fit in the housing.

How to choose the right blank end cap seal?

  • Bore diameter - The outside diameter of the seal must match the housing bore. Measure the bore carefully, as the seal relies on a tight fit.
  • Width - Check the width of the seal suits the depth of the bore, so it sits flush or at the correct depth.
  • Profile - Choose a standard flat seal for most bores, or a stepped seal to suit a bore with a shoulder.
  • Material - Nitrile rubber suits most oils, greases, and general applications. Check the seal is compatible with the oil or grease inside the housing.
  • Colour - Choose black for general use, or blue where easy identification is useful.

Essential references and specialised ranges

How the numbering works:

Blank end cap seals are referenced by type and size:

EC = end cap seal

VK = an alternative name for end cap seals, used by many suppliers

The size is given as outside diameter x width, in mm. For example:

EC85x9 = 85mm outside diameter, 9mm wide

EC140x15 = 140mm outside diameter, 15mm wide

EC150x27 = 150mm outside diameter, 27mm wide

Stepped seals show two thickness figures, for example ECY85x15/5.

Suffixes:

BLU = blue nitrile rubber

Y = stepped profile, shown with two thickness figures

Suffix codes vary between manufacturers, so check the supplier’s catalogue for the exact meaning.

FAQ - All you need to know about blank end cap seals

What is the difference between a blank end cap seal and an oil seal?

An oil seal has a hole in the middle and a sealing lip that runs on a rotating shaft. A blank end cap seal has a solid face with no hole, and is used to close off a bore where no shaft passes through.

Why are end cap seals called VK seals?

VK is a common alternative name used by many suppliers for blank end cap seals. Both names describe the same type of rubber-covered steel cap.

What is the difference between an end cap seal and an end cover?

An end cap seal presses into the housing bore and sits inside it, so it adds no width. An end cover usually fits over the outside of the housing, often with bolts, and sticks out beyond it.

Can I reuse a blank end cap seal?

It is best to fit a new one. Removing an end cap seal can damage the rubber or bend the steel body, which may stop it sealing properly when refitted.

How do I fit a blank end cap seal?

Clean the housing bore and remove any burrs or sharp edges. Lightly lubricate the outside of the seal, then press it in squarely using a flat plate or seal driver that covers the whole face. Push it in evenly until it sits at the correct depth. Never hammer directly on the seal.

How do I identify a blank end cap seal I need to replace?

The size is sometimes marked on the seal face. If it cannot be read, measure the housing bore diameter and the depth available, or measure the outside diameter and width of the old seal. Also check whether it has a stepped profile.

How can I tell if a blank end cap seal needs replacing?

Warning signs include:

  • Oil or grease leaking around the edge of the seal
  • Dirt or water getting into the housing
  • Cracked, perished, or hardened rubber
  • A bent or dented steel body
  • The seal moving, sitting unevenly, or working loose in the bore