
Carb Toroidal Roller Bearings
538 products
Loading filters…
Carb Toroidal Roller Bearings
What is a CARB toroidal roller bearing?
A CARB toroidal roller bearing is a single-row, self-aligning roller bearing made by SKF. It uses relatively long, slightly crowned rollers running between two concave raceways, with the outer raceway shaped like part of a torus (a ring-shaped curve). This design combines the self-aligning ability of a spherical roller bearing with the axial freedom of a cylindrical or needle roller bearing, in one compact bearing.
A standard bearing has four main parts:
- An inner ring with a concave raceway, which fits onto the shaft
- An outer ring with a toroidal raceway, which sits in the housing
- A single row of long, slightly crowned rollers
- A cage that keeps the rollers evenly spaced, or no cage on full complement versions.
The rollers are self-guiding.
- They move freely to the position where the load is spread most evenly, even when the bearing is misaligned or the rings have moved axially.
- This lets the shaft move axially inside the bearing with almost no friction, so no extra axial forces are created.
The bearing is non-separable, meaning the rings, rollers, and cage stay together as one unit. Rings and rollers are made from hardened bearing steel and are heat stabilised for use up to 200°C. Cages are pressed steel, glass fibre reinforced polyamide, or machined brass, depending on size.
Why are CARB toroidal roller bearings essential?
They solve a common problem on long shafts and heated rolls. When a shaft expands with heat or deflects under load, the non-locating bearing must allow both axial movement and misalignment. Normally that means a compromise: a spherical roller bearing allows misalignment but resists axial movement, while a cylindrical roller bearing allows axial movement but cannot tolerate misalignment. A CARB bearing does both.
They tolerate up to 0.5° of misalignment and let the rings move axially by up to about 10% of the bearing width, without harm to the bearing or its service life. This reduces internal forces, vibration, and heat, which can mean longer bearing life, smaller bearings, or lighter housings. They are intended only as the non-locating bearing and are paired with a locating bearing, such as a spherical roller bearing, at the other end of the shaft.
Typical applications include:
- Paper machines and drying cylinders
- Steelmaking, continuous casting, and rolling mills
- Conveyors and roller beds
- Fans and blowers
- Pumps and compressors
- Industrial and planetary gearboxes
- Crushers and vibrating screens
- Wind turbines and water turbines
- Ship propulsion and bow thrusters
- Food and beverage processing machinery
The main types of CARB toroidal roller bearings
- Caged CARB bearings - These are the standard design for heavy loads and relatively high speeds. Depending on size, they have a pressed steel, polyamide, or machined brass cage.
- Full complement CARB bearings (V) - These have no cage, so more rollers can be fitted, giving the highest load capacity for very heavy loads at low speeds.
- Tapered bore CARB bearings (K and K30) - These have a tapered bore and are mounted on a tapered shaft seat or on an adapter or withdrawal sleeve. The taper is 1:12 or 1:30, depending on the dimension series.
- Sealed CARB bearings - These have seals on both sides and are filled with grease, so they are lubricated for life and protected against contamination. Their misalignment, axial displacement, and load capacity are lower than open bearings.
- CARB bearings for vibrating applications - Special versions with case-hardened inner rings and hardened steel cages, for vibrating screens and other machines with high vibration.
- CARB bearings with increased axial displacement - Modified versions that allow even greater axial movement than the standard design.
How to choose the right CARB toroidal roller bearing?
- Size and dimensions - The bore must suit the shaft; the outer diameter and width must fit the housing. CARB bearings come in many of the same dimension series as spherical roller bearings, so they can often replace them directly.
- Load - Work out the radial load and whether it is steady or involves shocks. Compare it with the bearing’s basic dynamic load rating and basic static load rating, which are published in manufacturers’ catalogues. CARB bearings carry radial loads only, so a separate locating bearing must take the axial loads.
- Axial displacement - Check how far the shaft will move due to thermal expansion. The permissible displacement for each bearing is given in the catalogue, and mounting one ring offset from the other can increase it in one direction.
- Misalignment - CARB bearings tolerate up to 0.5° of misalignment between the rings. Sealed versions tolerate less.
- Caged or full complement - Caged bearings suit heavy loads and higher speeds. Full complement bearings suit very heavy loads and low speeds.
- Internal clearance - Choose the clearance to suit the fits and operating temperature. C3 is common where shafts run hot or interference fits are used.
- Bore type and sealing - Choose a cylindrical or tapered bore to suit the shaft, and a sealed bearing for dirty conditions or where relubrication is difficult.
Essential references and specialised ranges
How the numbering works:
The letter C at the start identifies a CARB toroidal roller bearing.
The next two digits indicate the dimension series, which match ISO series used for other bearings: for example, 22, 23, 30, 31, 32, 39, 40, 41, 49, 59, 60, and 69.
The last two digits indicate the bore:
From 04 upwards, multiply by five (for example, C 2210 = 50mm and C 2222 = 110mm)
For bores of 500mm and above, the bore is written in full after a slash, so a C 30/500 has a 500mm bore.
Suffixes:
K = tapered bore (taper 1:12)
K30 = tapered bore (taper 1:30)
V = full complement bearing, without a cage
TN9 = glass fibre reinforced polyamide cage
M = machined brass cage
No cage suffix = pressed steel window cage
2CS5 = synthetic rubber seals on both sides, filled with grease
C2 = radial internal clearance smaller than normal
C3, C4 = radial internal clearance greater than normal (C4 larger than C3)
HA3 = case-hardened inner ring
VG114 = hardened steel cage
VE240 = modified for greater axial displacement
Suffixes can be combined, for example C 2210 KTN9/C3. Check SKF’s catalogue for the exact meaning of less common codes.
FAQ - All you need to know about CARB toroidal roller bearings
What does “toroidal” mean?
A torus is a ring shape, like a doughnut. The outer raceway of a CARB bearing is shaped like part of a torus, which is what lets the rollers move both axially and at an angle while still carrying load.
What is the difference between a CARB bearing and a spherical roller bearing?
Both are self-aligning, but a spherical roller bearing has two rows of rollers and carries both radial and axial loads. A CARB bearing has one row of longer rollers, carries radial loads only, and allows the shaft to move axially inside the bearing. They are often used together, with a spherical roller bearing as the locating bearing and a CARB bearing as the non-locating bearing.
Can CARB bearings take axial loads?
No. They are designed only as non-locating bearings and carry radial loads only. Axial loads must be taken by the locating bearing at the other end of the shaft.
Do CARB toroidal roller bearings need lubrication?
Yes, lubrication separates the rollers from the raceways, reduces friction, and protects against corrosion. Open bearings can be grease or oil lubricated, while sealed bearings are filled with grease and are usually lubricated for life.
Click here to learn how to maintain a bearing.
Can I replace a CARB bearing myself?
In many cases, yes. Cylindrical bore bearings can be heated with an induction heater so they expand onto the shaft. Tapered bore bearings are driven up the taper or sleeve by the correct amount, checked by measuring the reduction in clearance or the axial drive-up. Make sure the rings are centred relative to each other after fitting, so the full axial displacement is available. Never strike the bearing directly with a hammer.
How do I identify a bearing I need to replace?
The reference is usually marked on the side face of the rings. If the markings are worn away, measure the bore, outer diameter, and width with callipers and match them against a size chart. Also check whether the bore is cylindrical or tapered, whether the bearing has a cage, and whether it is sealed.
Click here to learn how to measure a bearing.
How can I tell if a bearing is worn or failing?
Warning signs include:
- Grinding, rumbling, or clicking noises
- Increased vibration
- Rough or uneven rotation
- Play in the shaft
- Overheating
- Discoloured or contaminated lubricant